
Ornaments are the fastest way to make a Christmas wreath look finished, and the fastest way to make one look messy. A ball hung from a loose hook swings, spins to show its cap, and ends up on the porch floor after the third door slam. When we build holiday pieces in the workshop, ornaments get wired in, grouped and tucked so they stay exactly where we put them all season.
This is the method we use for both glass and shatterproof ornaments, along with the sizing rules that keep a wreath from looking like the ornaments were thrown at it.
Pick the right ornaments first
Where the wreath hangs decides what goes on it. For a front door, especially one that gets slammed or catches wind, shatterproof ornaments are the practical choice. They are lighter, they survive a fall, and they come in the same finishes as glass. Save real glass for wreaths hung indoors, over a mantel or on a wall where nothing bumps them.
Buy in three sizes rather than one. A good working mix for a standard 24 inch wreath is:
- A few large ornaments, around 100mm, as anchors
- A larger number of medium ornaments, around 60 to 70mm
- A handful of small ones, around 30 to 40mm, for filling gaps
A mix of finishes in one color family, such as shiny, matte and glitter in the same red, looks richer than many different colors.
Wire every ornament, never just hook it
The ornament cap is the weak point. On many ornaments it pops off with a light tug, so the first step is a small dab of hot glue under the cap to lock it to the ball. Let it cool before wiring.
Then thread a length of 22 or 24 gauge floral wire, or a chenille stem, through the cap loop. Fold it in half and twist the two ends together a few times right at the loop so the ornament cannot slide. Leave six to eight inches of twisted tail. If you are unsure which wire to keep on hand, our list of beginner wreath making supplies covers the gauges we actually use.
To attach, push the tail into the wreath and wrap it around the frame or a sturdy branch, not just the outer greenery. Twist it tight on the back and tuck the cut end in so it will not scratch your door. A wired ornament sits snug against the greens instead of dangling.
Build clusters before they go on
Single ornaments spread evenly around a ring look scattered. Clusters look designed. We wire ornaments together off the wreath in groups, then attach each group as one unit.
A basic cluster is three ornaments in odd sizes: one large, one medium, one small. Twist their wire tails together into a single stem, adjust so the balls touch and face slightly different directions, then attach that stem to the frame. Larger wreaths can take clusters of five or seven, built the same way with the large ball at the center.
A few habits that help:
- Turn caps toward the greenery so you see the ball, not the metal
- Let one ornament in each cluster sit a little deeper in the greens for depth
- Use a dot of hot glue where balls touch if the cluster wants to rotate
Place clusters with a plan
Placement is where most homemade wreaths go wrong. Before wiring anything permanently, lay the wreath flat and set clusters on top to see the balance.
For a full wreath, we usually work in a loose triangle: one main cluster where the bow will sit, and two smaller clusters spaced around the ring. For an asymmetrical look, mass the large ornaments in one lower corner and trail medium and small sizes outward from it. Either way, keep the biggest ornaments low and toward the focal area, since weight at the bottom looks settled.
Add the bow before the final fill so you know where the visual center is. If yours tends to flatten, our guide on how to make a bow for a wreath walks through building one that holds its shape. Once the bow and main clusters are on, step back six feet. If something feels lopsided, the reasons in why your wreath looks off usually point to the fix.
Fill gaps and test the hold
With clusters in place, use your small ornaments singly to fill thin spots and carry color between groups. Tuck them deep so they read as part of the greenery rather than sitting on top of it.
Then do the shake test. Hold the wreath upright and give it a firm shake, then a light knock as if a door closed. Anything that moves gets another wrap of wire on the back. For a door that sees a lot of traffic, a few extra wraps now will save you sweeping up glitter in December.
Shop finished pieces or learn with us
If you would rather have a holiday wreath that arrives already built this way, browse the one-of-a-kind pieces in our shop. If you want to make your own and get better each season, the Kreative Krew membership and our tutorials walk through wiring, clustering and placement step by step, right alongside us in the workshop.
Frequently asked questions
Can I use ornament hooks instead of wire on a wreath?
Hooks work for a quick indoor wreath, but they let ornaments swing, spin and fall. Floral wire or chenille stems wrapped around the frame hold ornaments snug and are the better choice for any door wreath.
How many ornaments do I need for a 24 inch wreath?
It depends on how full you want it, but a few large anchor ornaments, a larger group of medium ones and a handful of small fillers is a good starting point. Build clusters first and add more only where the wreath looks thin.
Should I use glass or shatterproof ornaments on a front door wreath?
Shatterproof is the safer choice for front doors because they are lighter and survive door slams and wind. Glass ornaments look lovely on wreaths hung indoors where they will not get bumped.


