Skip to content
Made once. Then it’s gone.Shop now

Technique · · 4 min read

How to Fluff a Faux Evergreen Wreath So It Looks Full

A layer-by-layer method for fluffing a flat, boxed faux evergreen wreath before you add décor, plus the common mistakes that leave gaps and bald spots.

By Kandi Jung · Kandi's Kreations, Savannah, Georgia

Detail of the lighted white church on a cardinal grapevine wreath

Almost every faux evergreen wreath ships the same way: pressed flat in a box, every tip folded toward the center, looking about half as full as the photo. That is normal. The fullness is in there, but it only shows up if you shape it, and how you shape it decides whether the finished piece looks lush or patchy.

In our Savannah workshop, fluffing the base is always the first job, before any ribbon, picks or ornaments. A well-shaped base means you need less décor to hide problems, and the décor you add sits better. Here is the method we use, layer by layer.

Before you start

Set the wreath face down on a clean table with good light. Wear thin gloves if the tips are wired PVC, because the cut wire ends can scratch. Give yourself 20 to 40 minutes for a standard door size; larger bases take longer.

Think of the wreath in three layers:

  • Back layer: the tips closest to the wall or door.
  • Middle layer: the tips that point straight out to the sides.
  • Front layer: the tips that face you.

You will work from back to front, all the way around, finishing each layer before starting the next. If you are still gathering tools, our post on beginner wreath making supplies covers what is actually worth buying.

Step 1: Shape the back layer flat

With the wreath face down, pull the back tips out so they lie nearly flat against the table, angled slightly outward. These tips are what keep light from showing through the wreath and what make it sit flush against a door.

Work in one direction around the ring. Do not skip around, because it is easy to miss a section and you will not notice until the wreath is hanging.

Step 2: Spread every tip, not just the stem

This is where most of the fullness comes from. Each main stem usually splits into smaller branchlets, and each branchlet has its own needles. Separate them.

  • Hold the stem near its base.
  • Fan the branchlets apart like fingers, some left, some right, one or two up.
  • Run your thumb along the needles of each branchlet to open them out.

A tip that is only bent away from the frame, but still bundled, adds almost nothing. A tip that is fanned and opened can look twice as wide.

Step 3: Turn it over and do the middle layer

Flip the wreath face up. Shape the middle tips so they point outward along the plane of the wreath, toward the outer edge and toward the inner hole. Alternate the angles slightly, a little up, a little down, so the side profile does not look like a flat shelf.

Pay attention to the inner ring. It is the area people forget, and a bare center hole is one of the first things the eye catches from the street.

Step 4: Bring the front layer forward

The front tips should angle toward you at roughly 45 degrees, not straight up. Straight up looks spiky and leaves gaps between rows. Angled tips overlap the ones behind them and fill the face.

Once the front is done, hang the wreath or prop it upright and step back six to eight feet. Look for spots where you can see the frame or light coming through. Adjust neighboring tips into those gaps rather than pulling new ones from elsewhere.

Common mistakes that leave gaps

  • Fluffing every tip straight out. You get a starburst with holes between the rays. Vary the angles.
  • Working face up only. Skipping the back layer leaves a hollow wreath that looks thin from the side.
  • Leaving branchlets bundled. Bending a stem is not fluffing it. Open every branchlet.
  • Rushing the inner ring. Bald centers show up in every photo of the door.
  • Judging up close. A wreath that looks fine at arm's length can look sparse from the walkway. Always check from a distance.
  • Covering gaps with décor. Picks and bows tucked into holes tend to droop and draw the eye to the problem. Fix the greenery first.

If your finished wreath still seems not quite right and you cannot tell why, our post on why your wreath looks off walks through the usual causes, from balance to scale.

A note on timing

A freshly unboxed base sometimes relaxes over a day or two, and a few tips may sag. It is worth fluffing, letting it hang overnight, and giving it a quick touch up before decorating. If you are planning ahead for next year, planning your Christmas wreath in the fall gives you time for exactly this kind of prep.

Ready to build, or ready to skip ahead?

If you would rather hang something that is already shaped and finished, every piece in the shop is one of a kind and built by hand in our workshop. If you want to learn to do it yourself, the Kreative Krew membership and our tutorials walk through bases, layering and décor step by step.

Frequently asked questions

How long does it take to fluff a faux Christmas wreath?

For a standard door size wreath, plan on 20 to 40 minutes if you open every branchlet. Larger or denser bases take longer.

Should I fluff the wreath before or after adding decorations?

Before. Shape the greenery completely first so you can see any gaps and fix them with the branches themselves, then add ribbon, picks and ornaments.

Why does my wreath still look thin after fluffing?

Usually the back layer was skipped, the branchlets were bent but not separated, or the tips all point the same direction. Check it from six to eight feet away and adjust tips into the visible gaps.

Put it into practice

The free intro course is the best first step.

Short beginner lessons — greenery, structure and the mistakes everyone makes first. No card, no supply list.

Keep reading

More from the workshop